• The contractor must provide all necessary services for the installation and use of AMSCO reprocessing sinks at a specified location to support manual cleaning procedures.
• NAICS code 561210 applies, focusing on facilities support activities for industrial and commercial buildings.
• Installation includes complete setup, training of clinical staff, and documentation of duty tours, with specific specifications for sink height, material type, and wall clearance required.
• Associated services include installation components, post-installation test, and adjustments, with a response deadline pending.
Description
STATEMENT OF WORK The contractor shall furnish all necessary services, labor, travel, transportation, materials, shipping, parts, connections, and equipment. This includes the provision and on-site installation of at least 5 AMSCO 50 Series Reprocessing Sinks at 4801 Linwood Blvd, Kansas City MO 64128. These reprocessing sinks are required by the Sterile Processing Services (SPS) to facilitate the manual cleaning of sterilization-compatible reusable medical devices (RMD) in invasive procedures. Their use will support a range of medical procedures and surgeries, including those in the operating room, dental services, procedural gastroenterology, procedural pulmonology and surgical clinics. The contractor bears the responsibility for the removal and disposal of all debris and packaging materials resulting from the reprocessing sinks installation. Prior to equipment utilization, the contractor is required to provide training to clinical staff, with all duty tours for the sterile processing department being documented. The scope of this contract comprises five AMSCO 50 Series Reprocessing Sinks. Associated services include complete installation components, execution of a post-installation check-out test, and implementation of any necessary adjustments. 2. SPECIFICATIONS Minimum of five 3 Bay 97.5” x 28” x 33”- 41” Adjustable Height Reprocessing Sinks. Installer Must Maintain a Minimum Gap of .875” To All Adjacent Walls as a Pinch Point Protection. Unit Must Be Installed Against a Wall, For Back-to-Back Installation a Pony Wall is Required. 304 Stainless Steel Construction. Pony Wall Must Be 53” Wall Must Be Free of Obstructions to 54” Utility requirements (plumbing) Hot Water (HW) Connection Type/Size- 3/8” COMPRESSION Pressure Range- 15 to 125PSI Operating Flow Rate- 1.6GPM @ MAX PSI Temperature Range 40° to 180°F Water Quality- Steris recommends the following water quality parameters: 100-200 PPM (500PPM MAX) TOTAL DISOLVED SOLIDS. 71-120 PPM (180PPM MAX) TOTAL ALKALINITY. 6.8-7.0PH (7.5 MAX). 0.1-0.5PPM (1.0) TOTAL SILICA. Cold Water (CW) Connection Type/Size- 3/8” COMPRESSION Pressure Range- 15 to 125PSI Operating Flow Rate- 1.6GPM @ MAX PSI Temperature Range- 70° F MAX Water Quality- Steris Recommends The Following Water Quality Parameters: 100-200 PPM (500PPM MAX) TOTAL DISOLVED SOLIDS. 71-120 PPM (180PPM MAX) TOTAL ALKALINITY. 6.8-7.0PH (7.5 MAX). 0.1-0.5PPM (1.0) TOTAL SILICA PURE WATER (PW) Connection Type/Size- ½” NPT Pressure Range- 20 TO 125 PSI Operating Flow Rate- .25 TO 2.0 GPM 15% Temperature Range- 40° F to 140° F WATER GUN (WG) Connection type/size- 3/8” Compression Pressure Range- 0 TO 44 PSI Temperature Range- 40° TO 125° Water Quality- Recommendations listed under #5 of (HW & CW) Air Gun (AG) Connection Type/Size- ¼” NPT Pressure Range- 30 PSI MAX Tip 1-5- Tip consumption at 30 PSI (Tip 4 and 5 must be operated at 30 PSI or less to comply with OSHA Directive. Basin Drain (BD) Connectio…
FedOps